DIY quilted scissor pouch

I love making useful items for gift giving around this time of year. I wanted to come up with a project for the blog that was sewing themed and would be a great present for a crafty friend…
introducing the DIY scissor pouch!

What you need for this project:

Paper

Pen

Ruler

Scissors – plus the pair you want to make the pouch for!

Main fabric – Treehouse Flying Squirrels by Figo Fabric (pictured below)

Lining fabric –Flower Market Spots cream by ABM  (pictured below)

Batting

Zip (the length of your scissors)

Swivel clip (optional)

Step One:

Lay your chosen scissors onto a piece of paper and leaving a couple of centimetres around the scissors mark a diagonal line.

I have the Fiskars Amplify scissors which are quite big so my height and width measured approx 15.5cm x 30cm for reference.

 

Step Two:

Use something curved to round off the two bottom corners of the pouch template.

Step Three:

Use your template to cut 2 each of main fabric, lining, and batting. The batting I used was an offcut from a quilt I made and is fairly light weight.

Step Four:

Take a piece of main fabric and batting and quilt them together. I did a simple grid pattern with the lines approx 2cm apart and on a diagonal angle but you can do this however you wish or skip this step altogether if you want.

Do the same for the other piece of main fabric and batting and now you have two complete outer pieces.

Step Five:

Now to add the zip! Place the zip face down on one of the main quilted pieces which should be right side up. Then layer on the lining facing down on the zip and stitch in place using a zipper foot.

Step Six:

Repeat step 5 for the opposite side of the zip and then open out both sides, press, and topstitch through all the layers on each side of the zip.

My zip was much longer than the zipper pouch so at this point I trimmed off the excess zip.

Step Seven:

This is an optional step but it makes a handy carrier for the pouch.

Measure a 3″ x 3″ square of fabric. Press a fold down the centre, then open ut and of each side into the centre and press. Topstitch 5mm down each side of the tab and then add on a swivel clip, pin it in place for the next step.

Step Eight:

Add the tab to the right side of the pouch approx 1″ down from the zip and pin/ clip in place

 

Step Nine:

Open your zip to the halfway point and then open out the layers of the pouch. Pin together the two lining pieces right sides facing and do the same with the main pieces right sides facing.

Stitch all the way around leaving a gap of about 3″ in the lining fabric to pull the pouch through after it’s stitched.

Step Ten:

Clip all the curved edges and then pull the pouch through to the right sides. 

Step Eleven:

Carefully poke out all the corners and give it a press then stitch the opening in the lining closed.

Et Voila!

This project is a great stash buster, would make a lovely gift, and would work in all types of woven fabric, you could even try making a faux leather one and omit the lining for a really quick make!

We hope you love this and if you do make one please tag us so we can share it!

Debbie x

#samanthaclaridgestudio

Handmade Valentine’s Bow Tie Tutorial

A handmade gift is the best way to show that special someone how much they mean to you. With a few bits of fabric and an hour or two you can whip up a funky bow tie and make the perfect Valentines day gift (a great one for Father’s day too!)

Here’s what you need:

Main fabric -Quilting Cotton like Figo treehouse works brilliantly

Fusible interfacing

A set of 19mm bow tie clasps

Loop turner or chopstick

Matching thread

Basic sewing kit

Step 1:

Cut the following…

Main fabric;

2 x 25cm x 14cm

1 x 4cm x 8cm

1 x 5cm x 55cm

Interfacing;

2 x 25cm x 14cm

1 x 4cm x 8cm

Apply the iron on interfacing to the wrong side of the fabric

Step 2:

Take one the of the 25cm x 14 cm pieces and measure the centre point on each end. Fold the fabric to meet this middle point and press.

Step 3:

Fold the ends to meet in the middle and stitch down either side of the middle seam as close as possible to the raw edge.

Do the same with the other main bow tie piece and then with wrong sides facing each other, sandwich the two pieces together and stitch down the centre

Step 4:

Take the 4cm x 8cm piece and stitch down one end and one side, trimming the seams and turning through and pressing, this will be the centre of the bow.

 

 

Step 5:

Do the same with the long 5cm x 55cm piece (use a loop turner or chopstick to help push the fabric right sides out) this will make the bow tie strap

 

Step 6:

Now add the slider part of the clasp onto the raw end of the long neck strap, threading through, folding over and stitching down turning the raw edge under.

Step 7:

Attach the hook part onto the strap, hook facing out. Then thread the other end of the strap back though the slider part, this makes your adjustable strap!

 

Step 8:

Attach the last piece of the clasp to the other end of the strap and stitch down.

Step 9:

Now to finish the bow part. Pinch the centre then bring the top and bottom edges in to meet the middle hand stitch in place

Step 10:

Hand stitch the bow to the neck strap between the adjuster and the clasp

 

Step 11:

Take the small bow centre piece and wrap around the middle of the bow and strap  hand stitching in place at the back of the bow.

Tag us #scsmakes if you do make one, we’d love to see it!